In‐Situ Observation of the Formation of MnS during Solidification of High Sulphur Steels

A Confocal Scanning Laser Microscope equipped with a gold image furnace was used to directly observe the precipitation of MnS during solidification of high sulphur steels under isothermal conditions in the temperature region 1440 to 1480°C on the free surface of the steel melt. For the case of Al‐killed steels, below 1480°C MnS particles were found to precipitate with Fe forming simultaneously around them. This MnS containing structure continued to grow rapidly (264 μm/s) as a surface film. The film gradually changed, as the level of S in the melt decreased, into a eutectic structure (with lamella spacing of 2 μm) as predicted by thermodynamics. In Si‐ killed steels there was significantly lower tendency to form MnS both in terms of time until precipitation occurred and growth rate.     

种分Δαk与种分首槽αk的关系

针对烧结法和拜尔法种分槽的 Δαk 变化进行了概述 ,阐述了种分 Δαk 与种分首槽 αk 的关系。     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

Lake-Level Change and Water Balance Analysis at Lake Qinghai,West China during Recent Decades

Lake Qinghai, the largest saline lake with an area of 4,260 km² (2000) and average depth of 21 m (1985) in West China, has experienced severe decline in water level in recent decades. This study aimed to investigate water balance of the lake and identify the causes for the decline in lake level. There was a 3.35-m decline in water level with an average decreasing rate of 8.0 cm year⁻¹ between 1959 and 2000. The lake water balance showed that mean annual precipitation between 1959 and 2000 over the lake was 357 ± 10 mm, evaporation was 924 ± 10 mm, surface runoff water inflow was 348 ± 21 mm, groundwater inflow was 138 mm ± 9 and the change in lake level was −80 ± 31 mm. The variation of lake level was highly positively correlated to surface runoff and precipitation and negatively to evaporation, the correlation coefficients were 0.89, 0.81 and −0.66, respectively. Water consumption by human activities accounts for 1% of the evaporation loss of the lake, implying that water consumption by human activities has little effect on lake level decline. Most dramatic decline in lake level occurred in the warm and dry years, and moderate decline in the cold and dry years, and relatively slight decline in the warm and wet years, therefore, the trend of cold/warm and dry climate in recent decades may be the main reasons for the decline in lake level.     

降雨空间分布模式识别

以广东省内186个站点的年降雨量分布为基础，把模式识别的聚类分析理论方法引入降雨空间特征分类研究中，进行降雨特征空间分布模式识别，以预测无雨量站点的降雨模式，从而分析水资源的空间分布模式，以便制订有效的水资源利用方案。结果表明，广东省年降雨量在空间上的分布可划分为6类模式；同时基于BP人工神经网络算法，建立了以高程、气温、蒸发量为主要参数的可判别和预测无雨量测站区域的降雨空间分布模式所属类别的模型，经过模型的学习和验证，效果较好。     

浸入凝胶法聚合物膜形成机理的研究现状

从热力学、传质动力学、相分离机制和固化过程几方面综述了浸入凝胶过程中聚合物膜形成机理的研究现状 .指出浸入凝胶成膜过程是传质交换和由传质交换引发的相分离以及其后的固化过程之间相互竞争的复杂非平衡过程 ,膜结构是上述几个过程竞争的结果     

3#大布袋收尘器更新改造方案的探讨

通过对3^#大布袋收尘器更新改造方案的对比分析，探讨适合工艺条件的最佳收尘器的选择途径。     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。